On the Air in Kentuckiana
Welcome

Welcome to the Amateur Radio Kentuckiana ham radio resource website.


Feel free to look around and find information including local Ham nets, repeater information, club info, license information, local Ham events and more.


73,

Louisville Ham Radio

Ham Tech

CES is this week. Will we see new Amateur Radio gear?

The 2015 Consumer Electronics Show is this week, and what could be more consumer electronic-y than some fresh new ham radio gear?

As in past years, I will be attending a couple days of the show for work and will keep an eye out for new amateur radio gear.  Unfortunately, previous attempts to be on the lookout for ham tech have been eminently disappointing.  I have found some manufacturers of cheap Chinese HTs and aftermarket batteries, but the Big 3 have been either absent or focusing on other market segments.

Maybe this year will be better with fewer e-cigs and bedazzled cell phone cases and more ham stuff.  If not, it’s only a short wait until the big Amateur Radio shindig at the NAB – where we’ll have the chance to win more goodies and rub elbows with the likes of Bob Heil and his tried-and-true “there, that sounds much better” shtick to open the event.

If you know of a CES exhibitor in the ham realm that we should check out, be sure to share it below in the comments.

The Amazing $130 Windows 8.1 SDR Gizmo

Toshiba Encore Mini with SDR dongleBy now, most hams have probably heard about the cheap SDR dongles that everyone is getting.  Meant for DVB-T use in other parts of the world, radio amateurs have figured out that these powerful, affordable devices are great for listening to local traffic across a sizable chunk of the RF spectrum.

All you have to do is just plug it into your computer’s USB port, fire up the software of your choice and you’re on your way to listening to local amateur, commercial, and aircraft traffic, tracking aircraft positions, and more.  If you’re a radio head, it’s (almost) the most fun you can have in front of your PC screen – but who wants to be stuck at their desk or mess with their laptop just to listen to a little radio?

If you like to go mobile with your tech, you’re living in a golden age.  The market is flooded with cheap, no-name Android tablets that may or may not work as well as their brand name counterparts.  Microsoft and other manufacturers have been cranking out Windows tablets, but the Windows RT versions are neutered and can’t run much useful ham software while the Windows 8.1 “Pro” models still have sky-high prices.  iPads… Well, some of the older models are coming down in price, but there just isn’t much there for radio amateurs.  Enter the new generation of affordable tablets.

Ingredients

For our demo, I’m using a Toshiba Encore Mini (WT7-CT16) – a 7″ touchscreen tablet with USB support that runs Windows 8.1 and has an MSRP of just $100 for the 8GB model that I got.  With flash memory chips’ capacity going up and prices going down, 8GB models are getting harder to find, though, so you may have to “settle” for the 16GB model.  I gather that the non-signature edition comes with some bloatware, but I’m not sure since I do have the MS signature version.  This is a pretty amazing deal, considering that an OEM copy of Windows 8 by itself costs about as much or more.  This tablet is perfect for this application (and lots of others!).  Since it runs a full version of Windows 8.1 and has a quad core Intel Atom x86 processor with a gig of RAM, it can run “real” Windows software.  Since it’s a touch screen, it doesn’t need extra gadgets like a keyboard or mouse to use it, although a stylus may help avoid “fat fingering” the controls.

Next, of course, we need the SDR dongle.  We’re using the Nooelec RTL2832 + R820T dongle.  The dongle, stubby antenna with cable and useless remote control sells for right around $20.  There is nothing Continue reading

A $20 SDR that Fits in Your Pocket?

_ne_r820t_1gA while back, some ingenious radio amateurs figured out that they could pair a $20 USB dongle meant for watching television in other parts of the world with some SDR software and listen to the ham bands (and more).

The “and more” part is what first caught my attention.  Much of the area uses digital trunked systems for their emergency communications and something like a TrunkTracker IV, despite being one of the more affordable pieces of equipment in this category, is still a bit out of my reach.  As someone who lives close to the site of a HAZMAT train derailment as well as a massive tire fire, and having had police chases that end in stand-offs go racing past my house, the ability to be “in the know” sounds like a good idea.  I haven’t got up and running with digital trunking systems yet (watch for a future post?), but I have definitely already got more than my $20 worth of use out of this gadget.

The first thing I did was order a Nooelec RTL2832U & R820TSB dongle.  Once it arrived, the package contained the USB dongle (which looks like a fat jump drive), a stubby little antenna with a few feet of coax and a small, mostly useless remote control.  I was ready to get started!   Continue reading

Build a Portable Universal Radio Programmer

What is it?

Many amateur radio transceivers allow users to set up memory channels to store their favorite simplex frequencies or repeater information including frequency (such as repeater name, frequncy, offset, tones and more).

Programming memory channels using the radio’s keypad can often be incredibly cumbersome and time consuming.

Using factory or homebrew programming cables can speed up the process but often introduces other issues (on top of the cost of having to purchase a programming cable for each radio).  Topping the list of those issues are usually driver problems that prevent the computer from being able to use the cable.  This method also means either having to take your radios to a computer or bringing the computer to your radios.

The project outlined in the document below will describe how to make a portable “universal” ham radio transceiver programmer.  The total cost of the project is around $40-50 (much less if you use parts you already have) and will yield a programmer that is approximately the size of a deck of cards, weighs only a few ounces and includes the computer and the cables you need to program your radio.  This programmer (perfect for travelers, emergencies and more) will connect to any display with HDMI or RCA video inputs and is powered by a standard USB power outlet, computer port or cell phone charger.

Build one today and keep it with your ham radio gear so you can program your radios on the go!

What You’ll Need

To build the programmer, you’ll need:

  • A set up Raspberry Pi computer (buy Raspberry Pi here)
  • Connectors for your specific radio
  • Soldering iron, solder and other items commensurate with building cables
  • About an hour of free time

To set up and use the programmer, you’ll need:

  • Standard computer interface devices (USB keyboard/mouse, HDMI/RCA display)
  • Micro USB power supply (cell phone charger, USB cable, etc.)
  • Radio

Build the Programmer

Convert a Computer Power Supply for Bench Use

What is it?

This one is pretty simple and the idea has been around for a while (see the “St. Louis Switcher”).  The idea is to take an ATX form factor power supply (available for free from dead computers everywhere), hack off some wires, add about $5 worth of parts from the electronics store (like MCM Electronics) or the junk bin and end up with a bench power supply that has enough power to run many mobile transceivers as base stations.

What You’ll Need

To build the power supply, you’ll need:

  • An ATX power supply with enough power for your job
  • An SPST (on/off) switch
  • A power resistor
  • Your favorite power connectors (Power Pole, binding posts, etc.)
  • Soldering iron, solder, wire cutters & strippers, heat shrink
  • Half an hour of free time

Build the Power Supply

At a recent hamfest, Chris KK4RZH gave us some info on a handy gadget to make an ATX PSU conversion even easier: A breakout board that plugs directly to the motherboard header pigtail to eliminate the need to all of the cutting, soldering, etc.  It should be noted that these breakout boards likely will not supply the current needed to operate a mobile ham radio transceiver.  However, they should work fine to charge batteries, operate QRP or other applications which use lower current.  Check out the breakout board here.

Support